Yale RS2 Bedienungsanleitung PDF herunterladen

PART NUMBERS FOR PACKAGED LUBRICANTS USED IN THE RS2 LEVER HOISTS

(REFER TO PAGE 6 FOR LUBRICATION INSTRUCTIONS)

LUBRICANT TYPE OF PART NUMBERS AND

USAGE LUBRICANT PACKAGED QUANTITIES

OF LUBRICANTS

3 TON LOWER SHEAVE BEARING GREASE-GRAPHITE 40626 (1 LB., .46 Kg. CAN)

JOURNALS AND SEAT FOR HOOK KNOB MIXTURE

(3/4 AND 1-1/2 TON)

TIP OF LEVER PLUNGER AND DRY-LUBE OIL- 40628 (1 PT., .5L CAN)

THREADED END OF PINION SHAFT GRAPHITE MIXTURE

INSIDE OF LEVER HEAD GREASE 40630 (1 LB., .46 Kg. CAN)

GEARS, LIFTWHEEL SPLINE, NEEDLE

BEARINGS, PINION BUSHING, CAM AND 28610 (1 LB., .46 Kg. CAN)

LOCK PINS, CAM SLOTS, AND I.D. OF CAM GREASE 28632 (4 LB., 1.8 Kg. CAN)

THREADS OF PINION SPRAY DRY 46698 (16 OZ. CAN)

LUBRICANT

LOAD CHAIN OIL 28608 (1 PT., .5L CAN)

When ordering lubricants, specify the type of lubricant, part number and packaged quantity required.

Touch-up paint for the RS2:

*(1) case (12-12 oz. Aerosol Cans) of Yellow Touch-up Paint Part Number 40215.

*Touch-up paints are only available in case quantities.

NOTE: When painting the hoists, also order warning labels and

capacity labels that may be coating during painting.

KEY NO. PART NAME PART NUMBER

NO. REQ’D. 3/4 TON 1 1/2 TON 3 TON

673-51 1 Hook Block Screw 40854 40855 –

673-52 - Load Chain (Specify Length Req’d.) 85839 85847

673-53 1 End Ring 40471

673-54 1 Capacity Label 73759 73751 73752

673-55 1 I.D. Label 73901 73903

673-56 1 Warning Tag 73905

673-57 1 Patent Label

(no longer available order 673-55)

–

673-58 1 Load Limiter Label (Only for units 73763

with Load Limiter)

673-59 1 Load Limiter (Optional) 7310 P 7311 P 7311 P

673-60 1 Cam Washer 73316

673-61 1 Anchor Sling 7309 P 7312 P –

*673-62 1 Lower Hook with latch (Latch type) -- 40606

673-63 1 Lower Hook Washer -- 50454

673-64 1 Lower Hook Nut -- 40382

673-65 1 Lower Hook Nut Pin -- 982335

673-66 3 Lower Hook Block Screw -- 940812

673-67 3 Lower Hook Block Screw L.W. -- 940830

673-68 3 Lower Hook Block Screw Nut -- 945820

673-69 1 Reeving Caution Plate -- 45757

673-70 1 Lower Sheave -- 40166

673-71 2 Lower Hook Block -- 40689

*673-72 1 Upper Hook with latch (latch type) -- 40606

673-73 1 Upper Hook Nut -- 40382

673-74 1 Upper Hook Nut Pin -- 982335

673-75 1 Hoist Hanger -- 73324

673-76 1 Dead End Pin -- 40851

**673-77 1 Upper hook block assembly (includes 73606 73607 -

673-16,673-30 and 673-35)

673-78 2 Lock Pin 73340 73342

* If latchlok hook is required, part numbers are: 3/4 ton upper and lower hooks - 1001, 1 1/2 ton upper and lower hooks - 1002

3 ton lower hook - 1004, 3 ton upper hook - 1010

** If latchlok hook is required, contact Yale.

Manual No. Y673-A

Before installing hoist, fill in the

information below.

Model No. __________________

Serial No. __________________

Purchase Date ______________

Rated Load _________________

73907 A

Capacities: 3/4, 1-1/2, 3 ton

(750, 1500, 3000 kg.)

Follow all instructions and warnings for

inspecting, maintaining and operating this

hoist.

The use of any hoist presents some risk of personal

injury or property damage. That risk is greatly increased

if proper instructions and warnings are not followed.

Before using this hoist, each operator should become

thoroughly familiar with all warnings, instructions and

recommendations in this manual. Retain this

manual for future reference and use.

Forward this manual to operator.

Failure to operate equipment as directed in

manual may cause injury.

OPERATING,

MAINTENANCE &

PA RTS MA N U A L

MANUALLY LEVER

OPERATED

CHAIN HO I S T

Lever Hoist

414 WEST BROADWAY AVENUE

MUSKEGON, MICHIGAN 49443

Note: When ordering parts, always furnish rated load and serial number of hoist on which the parts are

to be used.

For the location of the nearest Yale Authorized Hoist Parts Depot, see inside front cover.

LIMITATION OF WARRANTIES, REMEDIES AND DAMAGES

THE WARRANTY STATED BELOW IS GIVEN IN PLACE OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, NO PROMISE OR AFFIRMATION

OF FACT MADE BY ANY AGENT OR REPRESENTATIVE OF

SELLER SHALL CONSTITUTE A WARRANTY BY SELLER OR

GIVE RISE TO ANY LIABILITY OR OBLIGATION.

Seller warrants that on the date of delivery to carrier the goods

are free from defects in workmanship and materials.

SELLER’S SOLE OBLIGATION IN THE EVENT OF BREACH OF

WARRANTY OR CONTRACT OR FOR NEGLIGENCE OR

OTHERWISE WITH RESPECT TO GOODS SOLD SHALL BE

EXCLUSIVELY LIMITED TO REPAIR OR REPLACEMENT,

F.O.B. SELLER’S POINT OF SHIPMENT, OF ANY PARTS

WHICH SELLER DETERMINES TO HAVE BEEN DEFECTIVE or

if Seller determines that such repair or replacement is not

feasible, to a refund of the purchase price upon return of the

goods to Seller.

Any action against Seller for breach of warranty, negligence or

otherwise, must be commenced within one year after such cause

of action occurs.

NO CLAIM AGAINST SELLER FOR ANY DEFECT IN THE

GOODS SHALL BE VALID OR ENFORCEABLE UNLESS

BUYER’S WRITTEN NOTICE THEREOF IS RECEIVED BY

SELLER WITHIN ONE YEAR FROM THE DATE OF SHIPMENT.

Seller shall not be liable for any damage, injury or loss arising out

of the use of the goods if, prior to such damage, injury or loss,

such goods are (1) damaged or misused following Seller’s

delivery to carrier; (2) not maintained, inspected, or used in

compliance with applicable law and Seller’s written instructions

and recommendations; or (3) installed, repaired, altered or

modified without compliance with such law, instructions or

recommendations.

UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES AS

THOSE TERMS ARE DEFINED IN SECTION 2-715 OF THE

UNIFORM COMMERCIAL CODE.

INDEMNIFICATION AND SAFE OPERATION

Buyer shall comply with and require its employees to comply with

directions set forth in instructions and manuals furnished by Seller

and shall use and require its employees to follow such

instructions and manuals and to use reasonable care in the use

and maintenance of the goods. Buyer shall not remove or permit

anyone to remove any warning or instruction signs on the goods.

In the event of personal injury or damage to property or business

arising from the use of the goods, Buyer shall within 48 hours

thereafter give Seller written notice of such injury or damage.

Buyer shall cooperate with Seller in investigating any such injury

or damage and in the defense of any claims arising therefrom.

If Buyer fails to comply with this section or if any injury or damage

is caused, in whole or in part, by Buyer’s failure to comply with

applicable federal or state safety requirements, Buyer shall

indemnify and hold Seller harmless against any claims, loss or

expense for injury or damage arising from the use of the goods.

SS-5/2001

WARNING

ALTERATIONS OR MODIFICATIONS OF EQUIPMENT AND USE OF

NON-FACTORY REPAIR PARTS CAN LEAD TO DANGEROUS

OPERATION AND INJURY.

TO AVOID INJURY:

• DO NOT ALTER OR MODIFY EQUIPMENT

• DO USE ONLY FACTORY PROVIDED REPLACEMENT PARTS

414 WEST BROADWAY AVENUE

MUSKEGON, MICHIGAN 49443

1-866-805-2962 • Fax: 1-800-742-

1 2 3 4 5 6 ... 17 18

Inhaltsverzeichnis

Seite 1 - Lever Hoist

13PART NUMBERS FOR PACKAGED LUBRICANTS USED IN THE RS2 LEVER HOISTS(REFER TO PAGE 6 FOR LUBRICATION INSTRUCTIONS)LUBRICANT TYPE OF PART NUMBERS ANDUSA

Seite 2

6Also check chain for stretch using a vernier caliper as shownabove. Select an unused, unstretched section of chain(usually at the loose end) and meas

Seite 3 - SAFETY PRECAUTIONS

When lubricating parts adjacent to the brake, DO NOT usean excessive amount of lubricant which could seep onto thebrake surfaces.EXTERIOR FINISHThe ex

Seite 4 - 5 OPERATOR SERVICE

8J. Assemble pawls (673-19) to pawl shafts (673-22) andsecure with snap rings (673-32). Place pawl springs(673-21) on pawl shafts and insert these ass

Seite 5 - INSTALLATION

screw. If screw has been removed and replaced, alwaysuse new spots for locking.On the 3 ton unit, hang it in the vertical position. Makingsure there a

Seite 6 - OPERATION

KEY NO. PART NAME PART NUMBERNO. REQ’D. 3/4 TON 1 1/2 TON 3 TON673-1 1 Liftwheel Bearing 88645 88442673-2 1 Frame (includes 673-3 and (4) 673-4) 73304

Seite 7 - TO PULL OR LIFT LOAD

i 11 12Load Limiter(Optional)WARNINGUSING “COMMERCIAL” OR OTHERMANUFACTURER’S PARTS TO REPAIR THE RS2LEVER HOIST MAY CAUSE LOAD LOSS.TO AVOID INJURY:U

Seite 8 - WARNING

i 11 12Load Limiter(Optional)WARNINGUSING “COMMERCIAL” OR OTHERMANUFACTURER’S PARTS TO REPAIR THE RS2LEVER HOIST MAY CAUSE LOAD LOSS.TO AVOID INJURY:U

Seite 9 - Chain Inspection

13PART NUMBERS FOR PACKAGED LUBRICANTS USED IN THE RS2 LEVER HOISTS(REFER TO PAGE 6 FOR LUBRICATION INSTRUCTIONS)LUBRICANT TYPE OF PART NUMBERS ANDUSA

Seite 10 - LUBRICATION

13PART NUMBERS FOR PACKAGED LUBRICANTS USED IN THE RS2 LEVER HOISTS(REFER TO PAGE 6 FOR LUBRICATION INSTRUCTIONS)LUBRICANT TYPE OF PART NUMBERS ANDUSA

Seite 11 - ASSEMBLY

i 11 12Load Limiter(Optional)WARNINGUSING “COMMERCIAL” OR OTHERMANUFACTURER’S PARTS TO REPAIR THE RS2LEVER HOIST MAY CAUSE LOAD LOSS.TO AVOID INJURY:U

Seite 12 - REMOVAL OF LOAD CHAIN

iiSAFETY PRECAUTIONSEach Yale RS2 Manually Lever Operated Hoist is built in accordance with the specifications contained herein and atthe time of manu

Seite 13 - Cutting Chain by Nicking

iii1 CHOOSE THE RIGHT HOIST FOR THE JOB...Choose a Yale Lever Hoist with a capacityfor the job. Know the capacities of yourhoists and the weight of yo

Seite 14 - RS2 LEVER HOIST PARTS LIST

SPECIFICATIONSThe Yale RS2 Lever Hoist is a highly versatile manuallylever operated chain hoist that can be used to efficiently pull,lift, drag or str

Seite 15 - RS2 Lever Hoist

2Regardless of how the hoist is used, make sure that theupper hook is firmly attached to a support or anchor that hassufficient strength to hold sever

Seite 16

34. Pull on hook side and loose end side of load chain tomake sure chain feeds freely into and out of the hoist.5. Grasp unit by frame or upper hook a

Seite 17

4load the unit, then check to be sure that the attachments tothe hooks and load are firmly seated. Continue movementonly after you are assured the loa

Seite 18

5Inspection of hoists is divided into two general classificationsdesignated as “frequent” and “periodic”.Frequent InspectionsThese inspections are by

Kommentare zu diesen Handbüchern

Keine Kommentare

Yale RS2 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Schweißsystem Yale RS2 herunter. Yale RS2 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern